Wall-Mount Ladder Direct
Fixed Wall Mount Ladder
Wall-mounted fixed ladders with M12 anchor bolts and a 200mm standoff, trial-fitted at our factory before shipment. OSHA 1910.23/27 and EN ISO 14122-4 compliant builds.
Anchor Bolts
Rung Pitch
Rung Width
Rung Load Rating
Mounting & Anchors
Fixed Wall Mount Ladder
A wall-mounted fixed ladder is bolted to the structure through welded brackets with M12 anchor bolts. We hold rungs clear of the wall with a 200 mm standoff, and we trial-fit every ladder at the factory so the bracket pattern and anchor plan arrive ready to install.
- M12 anchor bolts — expansion or chemical, per wall substrate
- 200 mm standoff keeps toes and gloves clear of the wall
- Trial-fitted at factory — brackets, rungs and rail dry-assembled
- Rungs Φ20 mm at 280 mm pitch, 500 mm clear width
Build Options
Fixed Wall Mounted Ladders Options & Configurations
Three material families on the same M12 anchor pattern, plus rail and standoff options.
Galvanized Steel Wall Mount
Q235B with M12 anchors, HDG 85–100 μm. The standard for industrial walls and plant rooms.
Stainless Wall Mount
SS304 & SS316 for food, pharma and coastal walls — including stainless anchors and brackets.
Extended Standoff Mount
Cladding, insulation or pipe runs on the wall? We extend the bracket beyond 200 mm and re-verify the anchor load.
Dimensions & Standards
Fixed Wall Mount Ladder Specifications & Dimensions
Standard wall-mount geometry plus custom engineering for standoff, height, and anchor load. Every figure is on the shop drawing we send for approval.
Wall-Mounted, Any Height
From a 2 m step-up to a 14 m run — the anchor pattern scales with height, and the structural calc confirms it.
| Specification | Standard Range | Custom |
|---|---|---|
| Height | 2 – 25 ft (0.6 – 7.6 m) | Up to 40 ft engineered |
| Material | Q235B / SS304 / SS316 | Duplex / 6063-T5 AL |
| Rung Diameter | Φ20 mm (0.79″) | Per spec |
| Rung Spacing | 280 mm / 11″ (≤300 mm) | Per project spec |
| Clear Width | 500 mm (19.7″) | Custom width |
| Anchors | M12 expansion / chemical | Per substrate |
| Wall Standoff | 200 mm (7.9″) | Extended for cladding |
| Bracket Pitch | ≤1,500 mm vertical | Per structural calc |
| Load Rating | 1.5 kN per rung | Engineered |
| HDG Thickness | 85 – 100 μm (ISO 1461) | Heavier coating |
| Finish | HDG / Pickled / Painted | Electropolish (SS) |
| Fall Protection | None under 24 ft | PFAS rail over 24 ft |
Factory-Direct Wall Mount Pricing
Factory-Direct Pricing & 24h Quote
Itemized by material, bracket machining, anchors, finishing and packaging — no middleman markup.
Custom quotation priced by weight & process. Industry reference: fixed wall mount ladders ≈ USD 899–1,099/ton.
Certifications
Compliance & DoCumentation
- OSHA 1910.23 — wall mount rung & clearance rules
- OSHA 1910.27 — fall protection above 24 ft
- EN ISO 14122-4 — standoff & rung geometry
- BS 4211 & AS 1657 — wall fixings and clearances
Documentation Package
DoC, MTC and structural calcs — included, no paywall.
-
Declaration of Conformity (DoC)
-
Material Test Certificates — EN 10204 3.1
-
Structural Calculations (anchor & bracket loads)
-
Welding Procedure Specifications
-
Surface treatment certificates (HDG per ISO 1461)
Wall Mount to 50+ Countries
Trial-Fitted Here, Bolted On Site
Every wall mount is pre-assembled and dry-fitted before crating. VCI protection, ISPM 15 crates, EXW / FOB / CIF terms.
Common questions
2–25 ft (0.6–7.6 m) standard; taller runs are split into pre-assembled sections engineered from your drawing.
Q235B steel, SS304/SS316 and 6063-T5 aluminum, with HDG 85–100 μm, pickled or painted finishes.
8 mm standoff brackets at ≤1,500 mm vertical pitch, sized to the anchor plan for the substrate.
1.5 kN (≈337 lbf) per rung — anchor pull-out values are verified in the structural calcs with the order.
DoC, structural calcs and the HDG coating report — OSHA 1910.23/27 and EN ISO 14122-4 compliant, with every order.
Fastening & Substrate Selection
Fixed Wall Mount Ladder — Anchor and Substrate Choice
The wall mount is only as strong as the anchor and the substrate behind it. Match the M12 anchor family to the wall type and the 1.5 kN rung load holds for the life of the ladder.
Wall Mount Clearance & Fit
Every wall-mounted fixed ladder ships with an anchor plan, assembly drawing and M12 torque spec — no guessing on site.
M12 Anchor Selection by Substrate
| Wall Type | Anchor | Install Note |
|---|---|---|
| C25 concrete or better | M12 chemical resin anchor | Standard — highest pull-out, no torque relaxation |
| Concrete (light duty) | M12 mechanical expansion bolt | Faster install, review edge distances |
| Solid brick / block | M12 resin anchor + mesh sleeve | Requires structural review of the wall |
| Structural steel | Welded cleat or beam clamp | No drilling — bracket welded or clamped to the flange |
| Timber frame | M12 coach screw into studs | Only with engineered backing, per calcs |
Wall Mount Clearance & Fit
| Dimension | Standard | Compliance Note |
|---|---|---|
| Bracket steel | 8 mm standoff bracket | HDG 85–100 μm after welding |
| Standoff | 200 mm | Toe and glove clearance |
| Rung | Φ20 mm @ 280 mm pitch | 500 mm clear width |
| Load rating | 1.5 kN per rung | Anchor pull-out in the calcs |
| Top extension | 42 in (1.07 m) above landing | Safe egress per OSHA / EN ISO 14122-4 |
| Trial fitting | Dry-fitted at factory | Anchor holes pre-drilled to the bracket plan |
Fixed wall mount ladder questions
M12 chemical or mechanical anchors, selected by substrate — resin anchors for concrete, welded cleats or clamps for steel, reviewed resin installs for brick.
C25 concrete is the no-review standard. Weaker or hollow walls get a structural review and, where needed, a steel sub-frame before quoting.
Yes — we switch to welded cleats or beam clamps, no drilling, and the bracket layout is re-calculated for the flange.
200 mm standoff as standard, verified by the 8 mm bracket geometry and included in the drawing set.
Yes — the ladder is trial-fitted at the factory and anchor holes are pre-drilled to the anchor plan, so site install is bolt-up only.
Proven in real facilities
Reference projects are shown by industry, country and scale. Client names are available on request with approval.
National utility projects — 15+ countries
23 documented projects, 2021-2025 · 2025
All standardsEnergy & industrial clients — Global
500+ projects since 2004 · 2004-2025
Full compliance docsLargest single order — Malaysia
60 units in one project · 2021
HDGGet Your Wall Mount Quote
Talk to an Engineer
Send wall details — free drawing review and a fixed wall mount ladder quote in 24 hours.
Why Dengtai Wall Mounts?
Full Compliance Docs
DoC, MTC, structural calcs included free.
24-Hour Quote
Anchor plan + itemized quote within one day.
Trial-Fitted Shipment
Pre-assembled and dry-fitted before crating.
Request a Wall Mount Quote
Related Fixed Wall Mount Ladder Pages
Compare wall-mount options, install requirements, and compliance rules.
Wall Fixed Ladders
8mm bracket wall ladders with standoff
Cage Fixed Ladders
Φ700 safety cage configurations
Installation Requirements
Anchor plans, clearances and site prep
OSHA Fixed Ladder Rules
1910.23 rung rules and 1910.28 fall protection
Ladder Standards
OSHA, BS 4211, EN ISO 14122-4, AS 1657
Talk to an Engineer
Free drawing review, quote in 24 hours